Skip to content
EQPS

Equipment and SystemsLesson 6 of 6

EQPS 006

Data processing

Three areas of development

The ATC system processes the surveillance data and the flight plans, and both feed the user interface the controller works with (EQPS 001). Data processing has three major areas of development.

Data processing
THE ATC SYSTEMRadarFlight plansRadar dataprocessing systemFlight plan dataprocessing systemUser interfaceSafety toolsEfficiency toolsInformation exchangeOLDINeighbouring ATC unit
Information exchange
  • Between ATC unitsOLDI (below).
Safety tools
  • Conflict identification
  • Human error mitigationThe safety nets (below).
Efficiency tools
  • The controller's planning processThe planning tools (below).
The surveillance picture

The surveillance tracker

Surveillance data processing: the tracker builds tracks from the plots the sensors report (EQPS 004). It has six jobs.

Plots to tracks
Plots fromthe sensorsThe tracker1Plot to track association2Combines reportsfrom different sensors3Track smoothing4Estimates the currentspeed and heading5Track initiation6Track maintenanceRound again with each new plotTracks123456To the display
The six jobs run as a loop: the tracker goes round again with each new plot.
  1. Plot to track associationLinks a new plot to a track that already exists.
  2. Combines reports from different sensorsReports from different types of sensor feed the same tracks.
  3. Track smoothingUpdates the track with the latest plot.
  4. Estimates the current speed and headingOf the target, from its track.
  5. Track initiationStarts a new track from a plot that matches no existing track.
  6. Track maintenanceDeletes a track that is no longer updated, or predicts where it is from its last speed and heading.

Position indications and labels

What the controller sees on the display: the position indications, their labels, and the radar's vector line.

On the display
250° 18 NMKLM18SAS123240 450A320 MThe basic labelCall signCurrent level, ground speedAircraft type and waketurbulence categoryTrackPlotVector line, or QDM line
The shapes depend on the system. In class, a plot was drawn as a circle and a track as a square.
Position indicationsA plot and a track may look different.
  • PlotA position a sensor reports.
  • TrackWhat the tracker builds from the plots (above).
Vector line, or QDM lineA radar tool that measures distance and direction
  • From any point
  • Between two aircraft

Extended labels exist, with more. The leader line and the extended label: LAW 009.

Information exchange

Flight data processing and OLDI

Flight data processing, and OLDI, the information exchange that makes the coordination between ATC units automatic.

Flight data processingProvides real-time information. Automated coordination between neighbouring ATC units.
OLDI, On-Line Data InterchangeTransfers flight data and coordinates between units, so the coordination is automated (LAW 009).
Benefits
  • No need for verbal transmissionsNo calls, and no handling by hand, for the boundary estimates.
  • Timely acquisitionUpdated flight plan data arrives in time.
  • Integrity of dataNo human error in passing it on.
  • Accelerates the presentation of flight plan dataThe receiving controller sees it, with the call sign, sooner.
Disadvantages
  • If OLDI is down: work overloadThe estimates go back to voice, and the updates to the system by hand.
  • Unfamiliar procedures
  • Lack of staffTo pass the estimates and update the system by hand.

The OLDI messages

Six messages: four exchange the flight data automatically, and two, for the transfer of communication, are manual.

Automatic: flight data exchange
  • ABI, Advance Boundary InformationAdvance notice of the flight to the next unit.
  • ACT, activate messageThe coordination itself. It replaces the verbal estimate.
  • REV, revision messageChanges data already sent in the ACT.
  • LAM, logical acknowledgement messageThe automatic reply to each message.
Manual: transfer of communication
  • ROF, request on frequencyThe accepting unit asks for an early transfer of the flight.
  • HOP, hand-over proposalProposes the flight for hand-over.
The coordination process

A flight about to cross from one area of responsibility (AoR) to the next, at the coordination point (COP). The two units' OLDI servers coordinate it.

Before the COP
AoR 1Area of responsibility 1AoR 2Area of responsibility 2ABIACTCOP: coordination pointOLDI serverOLDI serverABIAdvance noticeLAMReplyACTCoordinationLAMReply
First the ABI, early, then the ACT, both before the flight reaches the COP. A LAM answers each one.

The ACT does not activate the flight plan. It is the coordination, in place of the verbal estimate. A flight plan is activated by the DEP message (LAW 007).

Safety nets and planning tools

Safety nets

Two kinds, by where they work: airborne safety nets alert the pilot, and ground-based safety nets alert the controller.

AirbornePilot safety nets: they alert the pilot
  • ACASAirborne collision avoidance system, ICAO's name.
  • TCASTraffic alert and collision avoidance system: the ACAS aircraft carry (ATM 006).
  • GPWSGround proximity warning system.
  • EGPWSEnhanced ground proximity warning system.
  • TAWSTerrain avoidance and warning system.
Ground-basedATCO safety nets: they alert the controller
  • STCAShort term conflict alert.
  • MSAWMinimum safe altitude warning.
  • APWArea proximity warning.
  • Not intended to replace ATC.
  • The last defence.
  • Their presence is ignored when sector capacity is calculated.

STCA, MSAW and APW

The three ground-based safety nets, and what each warns the controller of.

STCASTCAAAL221STCAKLM18

Two aircraft on converging tracks: STCA shows on both labels.

  • Short term conflict alert
  • Helps the controller prevent collisions between aircraftIt alerts to a potential or actual loss of separation.
  • Sufficient warning timeUp to 2 minutes before separation is lost, where possible.
  • False alertsKept to a minimum.
MSAWMinimum safe altitude
  • Minimum safe altitude warning
  • Alerts the controllerWhen an aircraft is, or will be, below the minimum safe altitude.
APWR areaUp to 2 minutesAPWSAS123
  • Area proximity warning
  • Warning timeUp to 2 minutes before.
  • Warns about TRA and TSA, R, P and D areasWhen an aircraft is, or will be, flying into one (LAW 004).
  • Also: a flight with no ABI

A fourth ground-based safety net, APM, approach path monitor, gives the same warning as MSAW on final approach (LAW 009).

Monitoring and planning tools

Two more kinds of ground tool: the monitoring aids, which show a flight leaving its route or its level, and the planning tools, which help the controller plan ahead.

RAMPlanned route
CLAMCleared level
Monitoring aids
  • RAM, route adherence monitoringHighlights a flight leaving its planned route.
  • CLAM, cleared level adherence monitoringHighlights a flight leaving its cleared level.
Planning tools
  • FLEG, flight legProjects the aircraft's predicted path.
    FLEG is the name in the course's system.
  • MTCD, medium term conflict detectionA controller support tool.
    It searches for conflicts up to 20 minutes ahead.
    It uses the trajectory to find conflicting paths.
  • AMAN, arrival managerOptimises the use of the runway, and the arrival traffic.
How far ahead
STCAUp to 2 minutesAPWUp to 2 minutesMTCDUp to 20 minutesNow2 min10 min20 min
The safety nets look a short time ahead; MTCD plans a much longer way ahead.

MTCD is a planning tool, not a safety net. It looks up to 20 minutes ahead; STCA up to 2.

Reading material