Skip to content
EQPS

Equipment and SystemsLesson 4 of 6

EQPS 004

Radar systems

Surveillance

The concept of surveillance

A sensor, or a network of sensors, that does three things.

  1. Detects aircraft
  2. Works out their position
  3. Gets other dataSuch as identification and level.
Four major surveillance systems give target data
Target data
IdentitySpeedPositionAltitudeSensor
Separation based on surveillance
Separation
0510 NMwithin 10 NM of the runway threshold.5 NMThe standard.3 NMWhere the surveillance system'scapabilities allow.2.5 NMBetween aircraft on the same final approach track,

By radar, ADS-B or MLAT. 5 NM is the standard, and the appropriate ATS authority may reduce it, but never below these two (ATM 003).

Surveillance domains

Three domains: who is watched, and from where.

Three domains
ADS-B outADS-B inSMRADS-BMLATSSRPSRAir/ground surveillanceAir/air surveillanceGround/ground surveillance
Air/ground surveillanceFrom the ground, of aircraft in the air.PSRSSR

The radars of this lesson.

Air/air surveillanceBetween aircraft in the air.ADS-B outADS-B in

ADS-B is in EQPS 005.

Ground/ground surveillanceFrom the ground, of what moves on the ground.SMRADS-BMLAT

SMR is below. MLAT is in EQPS 005.

The names
PSRPrimary surveillance radar
SSRSecondary surveillance radar
SMRSurface movement radar
Mode SSelective SSR
MLATMultilateration
ADS-BAutomatic dependent surveillance broadcast

The radars at a glance

The four radars of this lesson side by side; each name opens its section.

The four radars of this lesson side by side.
PSRSSRMonopulse SSRMode S
How it finds the aircraftA pulse out, an echo backAn interrogation on 1030 MHz, a reply on 1090 MHzAs SSR; it compares the left and right halves of its antenna to find the directionAn all-call finds it; then it calls it on its own, by its address
How it is sortedIndependent and non-cooperativeIndependent and cooperativeIndependent and cooperativeIndependent and cooperative
What it givesRange and azimuthRange and azimuth; Mode A and CRange and azimuth; Mode A and CElementary and enhanced surveillance
ForWorks with passive echoesNo clutter, long-range coverage, emergency signallingImproved accuracy, fewer replies neededUnambiguous aircraft identification, a solution to the code shortage
AgainstNo identification, no height information, clutter and false plotsRequires a transponder, only 4096 codes, garbling, FRUITRequires a transponderRequires a transponder and a monopulse radar
How it is sorted

Two pairs of words, as in EQPS 001: who works out the aircraft's position, and whether the aircraft's equipment takes part.

Who works out the position
DependentThe aircraftThe aircraft works out its own position, with systems on board, and sends it.
vs
IndependentThe groundThe ground works out the aircraft's position.
Does the aircraft take part
CooperativeEquipment on boardThe aircraft's equipment takes part.
vs
Non-cooperativeNothing on boardPassive reflection only: no equipment on board is needed.
PSRIndependent and non-cooperative.
SSR, Mode S includedIndependent and cooperative.

Primary radar (PSR) is the only non-cooperative surveillance.

It is not the only independent one. SSR is independent too: there, as with PSR, the ground works out the position.

Primary radar

How primary radar works

Primary surveillance radar, PSR, is independent and non-cooperative. It is used en route and on approach.

A pulse outIt sends out a high-power pulse of radio waves.
An echo backThe pulse reflects back off an aircraft, or any other object it hits: the echo.
Primary radar
DuplexerTransmitterReceiverProcessorDisplayAntennaPulseEcho
One antenna does both: the duplexer switches it between sending the pulse and hearing the echo.
  • AntennaSends the pulse out and picks up the echo.
  • DuplexerSwitches the antenna between the transmitter and the receiver.
  • TransmitterMakes the short, high-power pulses.
  • ReceiverAmplifies the weak echoes.
  • ProcessorAnalyses the echoes and picks out the moving targets, for the display.
  • DisplayShows the targets to the controller.

Slant range

The radar times how long the echo takes to come back, and works out the range from that.

Slant range (NM) = speed of light × detection time divided by 2
Primary radar
Slant range:the longer sidePulse outEcho backAlong the ground: the shorter sideHeightTimeDetection time÷ 2
The pulse goes out and the echo comes back, so the detection time covers the slant range twice: that is why the formula halves it.
Slant rangeThe straight-line distance from the antenna to the aircraft. It is longer than the distance along the ground.
Detection timeThe time from sending the pulse to receiving the echo.
Divided by 2The pulse goes out and back.

Azimuth and the sweep

The antenna sends its pulses in a narrow, fan-shaped beam that sweeps round all 360°. The radar knows which way the antenna points, so each echo gives a direction, the azimuth, as well as a range.

Seen from above
N255075 NMTargetSweepThe beam turns 360°AzimuthThe direction, from northRangeThe distanceRange ringsEvery 25 NM
Range and azimuth together fix the target's position. The beam passes over each target once a turn.
What the radar gives
2D radarRange and azimuthOnly those two. Most ATM radars are 2D.
vs
3D radarAlso elevationAlso gives the elevation, so the altitude. Common in weather monitoring and defence: weather and military radars are 3D.
The cone of silence

The area straight above the radar's antenna, which the radar does not cover.

Seen from the side
FL 300About 20 to 40 NM wideCone of silenceNot coveredCoveredCovered
Not to scale. The cone gets wider with height: at FL 300 it is about 20 to 40 NM wide, depending on the radar.

Clutter

Echoes from things that are not aircraft: other things reflect the pulse too, such as weather.

Seen from the side
ClutterEchoes, not from an aircraftHidden in itHidden behind itThe radar is blinded
Clutter can hide an aircraft inside it, and blind the radar to an aircraft behind it.
It can hide aircraftAn aircraft in the same area as the clutter is lost in it.
It can blind the radarThen it also hides the aircraft on the far side of it.
Signal processingRemoves the echoes that do not move. It is the first step from echo to track (Plots and tracks, below).

Other primary radars

Three more radars that work on the same principle: a pulse out, an echo back.

Surface movement radarA kind of PSR.SMR

Covers the manoeuvring area.

Short range, a high update rate and high resolution.

Precision approach radarA primary radar.PAR

Gives an aircraft lateral and vertical guidance for landing.

It shows the aircraft's deviation on final, and the controller guides the pilot by radio.

Weather radarIt works on the same principles as PSR.

Detects precipitation: raindrops and snow.

PSR: for and against

What primary radar does well, and where it falls short.

For
  • Works with passive echoesReflections: it needs nothing on board the aircraft.
Against
  • No identificationIt cannot tell which aircraft is which.
  • Attenuation of the radio waveThe wave weakens on its way (EQPS 002).
  • Clutter and false plots
  • No height information

The solution: SSR, secondary surveillance radar (below).

Secondary radar

How secondary radar works

Secondary surveillance radar, SSR, is independent and cooperative. In place of an echo, it gets a reply from the aircraft's transponder.

Secondary radar
InterrogatorTransponderInterrogation1030 MHzReply1090 MHzMode A: identityMode C: pressure altitudeTime
The ground asks on 1030 MHz, and the transponder answers on 1090 MHz.
InterrogatorThe SSR on the ground. It sends the interrogation, on 1030 MHz.
TransponderOn board: a “transmitting responder”. It responds to the SSR's question, the interrogation, with a reply on 1090 MHz.
Mode AIdentity: the squawk code, set on the transponder.
Mode CThe pressure altitude: measured on the standard setting, 1013.25 hPa, as a flight level is (ATM 005).
IDENT
  • Pressed by the pilot only when ATS asks
  • Highlights the aircraft on the radar screenTo help the controller find it.
  • Can also help with a radio failureAn aircraft that can still hear can answer with an IDENT.

Squawk codes

A Mode A code has four digits, each from 0 to 7: from 0000 to 7777, so only 4096 codes.

Mode A
01234567012345670123456701234567000077770 to 7Only 4096 codes
Two kinds of code
DiscreteOne flightA code ATC assigns to one flight.
vs
ConspicuityNon-discrete: many flightsMany flights can use the same code. Non-discrete codes end in 00, as all three below do.
ORCAMThe originating region code assignment method: ICAO's method for assigning codes, which the European code plan is based on.
CCAMSThe centralised code assignment and management system: in Europe, EUROCONTROL runs it and assigns codes centrally.
The codes to learn by heart

In test mode the answers are hidden. Click or tap a card to reveal it.

Conspicuity codes
1000 Mode SThe Mode S conspicuity code.
2000 No code assigned by ATCIn Denmark, an IFR flight.
7000 VFR, with no code assignedTypically outside controlled airspace.
Reserved codes
7500 Unlawful interference
7600 Radio communication failure
7601 IFR communication failure in VMCEuropean only, from SERA since May 2025: the flight carries on in VMC and lands at the nearest suitable aerodrome.
7700 Emergencies and interception

The reserved codes in the alerting service: ATM 004.

Plots and tracks

Plots are the raw material of tracks. The echoes of PSR and the replies of SSR go the same way to the screen.

From the radar to the screen
PSRSSRSignalprocessingPlotextractionSurveillancedataprocessingDisplay at theworking positionPlotsTracks
Echoes and replies become plots, and plots become tracks, on the way to the display.
  • Signal processingKeeps the wanted signals and removes the unwanted, such as echoes that do not move.
  • Plot extractionMakes a plot, a target report, from the echoes or the replies: range and azimuth, and from SSR the Mode A code and the Mode C altitude too.
  • Surveillance data processingThe plots are distributed to it, and it builds the tracks: tracking.
  • DisplayShows the tracks at the working position.

How the tracker builds the tracks: EQPS 006. What a plot and a track are on the display: LAW 009.

What can go wrong

Each interrogation should bring one clean reply. An SSR needs many of them to make a plot. Three things can go wrong.

One interrogation, one replyPerfect

The reply comes back clean, apart from any other.

One interrogation, several close repliesGarbling

Two aircraft close together reply at the same time, and their replies overlap.

No interrogation, several repliesFRUIT

False replies unsynchronised in time: replies the radar did not ask for, sent to another radar's interrogation.

One interrogation, no replyNo reply

Transponder failure, out of range, or antenna shadowing (EQPS 003): the aircraft itself hides its transponder's antenna from the radar, as in a turn.

SSR: for and against

What secondary radar adds, and what still goes wrong.

For
  • Mode A and CThe aircraft's identity and its pressure altitude.
  • No clutterIt listens for replies on another frequency, 1090 MHz, not for echoes.
  • Long-range coverageThe interrogation and the reply each only travel one way.
  • Emergency signallingWith the reserved codes.
Against
  • Requires a transponder
  • Only 4096 codes
  • Garbling
  • FRUIT
  • Reflection and multipathA reply that bounces off a building or the ground reaches the radar by more than one path, and can show a false target. How a wave reflects: EQPS 002.

The solution: Mode S, which needs a monopulse radar (below).

Monopulse and Mode S

Monopulse SSR

MSSR, monopulse SSR: its antenna is divided into a left and a right half, which it compares.

Seen from above
Boresightwhere the antenna pointsAircrafta little right of centreIts reply reachesthe right half firstSame distancefrom the aircraftPath lengthdifferenceLeft halfRight halfThe MSSR antenna
From the difference between the two halves, the MSSR finds the aircraft's direction within the beam.
Improved accuracyBetter azimuth resolution: the direction is found within the beam.
Fewer replies needed3 to 8 to find the position (the course slide says pulses), so less garbling and FRUIT.
Mode A and C tooAn MSSR also works with Mode A/C transponders.

An MSSR does not need Mode S. It is the other way round: Mode S needs a monopulse radar.

The Mode S transponder

Mode S, selective SSR: each aircraft has its own address, so the radar can call it on its own.

All-call and roll-call
All-callB25FC7Squawk 1000Roll-call
Mode S interrogations
All-callA search callFinds the aircraft not already acquired.
vs
Roll-callA selective interrogationCalls one aircraft, by its address.
ICAO aircraft addressUnique to the aircraft: 24 bits, written as six hexadecimal digits, 0 to 9 and A to F, such as B25FC7. 24 bits: about 16.7 million addresses.
Squawk 1000The Mode S conspicuity code.
Mode A and C still workA Mode S transponder still answers Mode A/C interrogations.

The address is not a squawk. A squawk code has four digits from 0 to 7; the address, six hexadecimal digits. That is why it is called an address.

What Mode S sends

Elementary surveillance comes first. Enhanced surveillance adds more: the downlink aircraft parameters, DAPs.

Elementary surveillance
  • Range and azimuthMeasured by the MSSR.
  • Aircraft identificationThe call sign, reported automatically.
  • AltitudeIn 25 ft steps.
  • Flight statusAirborne or on the ground.
Enhanced surveillance: DAPs
  • Roll angle
  • Selected altitudeThe level the crew has selected.
  • Ground speed
  • Magnetic heading
  • Indicated airspeed and Mach number
  • Vertical rate
  • TCAS resolution advisoriesFrom TCAS, the traffic alert and collision avoidance system on board (ATM 006 and EQPS 006). Sent today.
ForMode S: the benefitsWhat Mode S brings to ATC.
  • Unambiguous aircraft identificationA unique address: no more wrong code settings.
  • Improved integrity of surveillance dataSelective interrogation: less garbling, fewer false replies.
  • A solution to the code shortage
  • Improved controller situation awarenessThe aircraft's data at once, in place of asking for it.
  • Improvements to safety netsSuch as those of EQPS 006.

Mode S is still independent surveillance: the ground works out the position.

Reading material