Skip to content
ACFT 002

Pilot controls and aircraft engines

Pilot controls

The three axes

The primary flight controls are the ailerons, the rudder and the elevator. Each turns the aircraft about one of its three axes.

PitchLateral axisRudderElevatorRollLongitudinal axisYawVertical axisAileronsPITCHLateral axisYAWVertical axisROLLLongitudinal axis
Each view shows the turn about the axis that points at you, marked as a ring with a dot. The green surfaces make the turns.
Where they meetThe three axes are imaginary lines through the aircraft’s centre of gravity, each at right angles to the other two.
Longitudinal axisRuns from the nose to the tail. The aircraft rolls about it: it rotates, one wing rising as the other falls. The ailerons control roll.
Lateral axisRuns from wingtip to wingtip. The aircraft pitches about it: the nose moves up and down. The elevator on the tailplane controls pitch.
Vertical axisRuns from top to bottom. The aircraft yaws about it: the nose moves left and right. The rudder on the fin controls yaw.
Learn by heart

In test mode the answers are hidden. Click or tap a card to reveal it.

Pitch Lateral axisNose up and down: the elevator
Yaw Vertical axisNose left and right: the rudder
Roll Longitudinal axisRotation: the ailerons
Yoke Controls the ailerons and the elevator
Pedals Control the rudder

Secondary control surfaces

Five more surfaces, on the wings and the tail.

  1. SlatSlatsAn extension on the leading edge. Lets the wing work at a higher angle of attack.
  2. FlapFlapsMounted on the trailing edge, and deflected down to increase the curvature of the wing. They increase lift, which reduces the stall speed, and they increase drag: they act as an air brake.
  3. SpoilerSpoilers (lift dumpers)Extend upwards on the wing to reduce lift and increase drag.
  4. Speed brakesSpeed brakesUsed to increase drag.Usually surfaces that deflect outwards from the fuselage. They do not directly change the lift of the wing.
  5. ElevatorTrim tabTrim tabsA small control surface connected to the trailing edge of a larger control surface. Adjusts the resting position of the control surface.
Engines and fuel

The piston engine

The piston engine is a four-stroke engine. Its pistons are connected to the crankshaft, which turns the propeller.

  1. 1 InductionThe air and fuel mix is sucked in.
  2. 2 CompressionThe mix is compressed and ignited.
  3. 3 PowerThe gas expands and pushes the piston down.
  4. 4 ExhaustThe piston moves up again and pushes the burned gas out through the exhaust valve.
The green arrow is the way the piston moves. Blue is the air and fuel mix, orange the burning gas.
CarburettorAirFuelExhaust valvePistonCrankshaft1 Induction2 Compression3 Power4 Exhaust
The carburettor vaporises the fuel and mixes it with the air, on its way into the cylinder.

Carburettor icing is the carburettor's most common malfunction.

The propeller

The propeller converts the power into thrust. It is driven either directly or through a reduction unit.

  1. EngineThrustPropellerCrankshaftDirect driveThe crankshaft turns the propeller itself.
  2. EngineThrustPropellerReduction unitCrankshaftThrough a reduction unitThe crankshaft turns the propeller through the reduction unit.
Fixed pitchOne blade angle: a compromise between cruising speed and climb performance.
Variable pitchThe pilot can change the pitch in flight, for the best climb, cruise or descent.
Variable pitch: feathering and thrust reverse
  1. AirflowTurningPitchPitchThe angle of the blade.
  2. AirflowFeatheringThe blades turn parallel to the airflow, to reduce drag after an engine failure.
  3. AirflowTurningNegativeangleThrust reverseThe blades turn to a negative angle, to direct the thrust forward.
Each blade cut across and seen from its tip. The dashed line is the line the blade turns along.

The blades are twisted: the blade angle changes along the blade, because each part of it turns at a different speed, faster towards the tip.

Jet engines

A jet engine is ram powered or turbine powered.

Jet engine
Ram powered
  • Ramjet
Turbine powered
IntakeCompressionCombustionTurbineExhaustCold sectionHot sectionCompressor
The turbine drives the compressor.
Cold sectionIntake and compression.
Hot sectionCombustion, the turbine and the exhaust.

In a turbofan, part of the air goes round the core instead of through it: the bypass. Airliners have high bypass engines, fighters low bypass engines.

The turboprop

In a turboprop the turbine powers the propeller, and about 90 % of the thrust comes from the propeller.

About 90 %of the thrustPropellerGearboxCompressorCombustionTurbine
The turbine turns the propeller through the gearbox.

A turboshaft is for helicopters.

Engines compared

What each engine does well, and where it falls short.

Piston engineJet engineTurboprop
For
  • Power changes almost instantly
  • Cost efficient
  • Economic at low levels and low speeds
  • High thrust to weight ratio
  • Low vibration
  • Mechanically efficient and reliable
  • Fast
  • Great fuel efficiency at high levels
  • High thrust to weight ratio
  • Less vibration than a piston engine
  • Higher speed than a piston engine
  • Can operate on a short runway
Against
  • No high speeds or high levels
  • High maintenance
  • High vibration
  • Considerable drag
  • Expensive
  • Power changes slowly
  • Only economical at high levels
  • Not great at high levels
  • Expensive compared to a piston engine
  • En-route weather causes limitations

Fuel

Piston engines and turbine engines take different fuels.

  • AVGAS 100LLAVGAS, aviation gasoline100LL: low lead.High octane, for piston-powered aircraft.
  • Jet A-1Jet fuelKerosene based.For turbine engines: jets, turboprops and turbine helicopters.
  • SAFSAF, sustainable aviation fuelMade from renewable sources or waste.A biofuel is one example.

Reading material